I love HSTs and then I love charm squares. That need not be mentioned again. You guys know it by now! I have said it a hundred times and more, then again, just one more time… 🙂

I am participating in 2 mug rug swaps and wanted to send my partners some really colourful, spring type mug rugs. While I was browsing through Pinterest, I chanced upon these lovely pinwheels and wanted to make a few. The only challenge being, mine had to be 5″ square. As an experiment I cut all my fabric in 5″ square.

Fabric Requirement for one Mug Rug:
2 charm squares in printed fabric(mine has flowers)
2 charm squares in a single solid(mine are in magenta)
4 charm squares in a neutral solid colour for the base
10 X 10″ batting (I used flannel)
10 X 10″ backing in a solid colour

1. Start by placing one solid charm square on a printed one, right sides together.
2. Draw a diagonal line from corner to corner on the wrong side of fabric.
3. Sew 2 parallel lines on either side of the diagonal line at a distance of 0.25″ and cut on the diagonal line.
4. Press fabric on wrong side, with extra fabric folding onto darker side fabric. Trim the little dog ears at the end.
5. Similarly make all the 4 HSTs.Turn at the diagonal and press the triangle .

Here are the lovely colourful HSTs. I am making 4 mug rugs in different colours and hence the bunch of candies 🙂

Pinwheel 1

6. Take a neutral charm square(right side up) and align the folded triangle on it such that the corners align. Fold the triangle in half to make a smaller triangle and pin.
7. Do this will all 4 HSTs and neutral fabric. Arrange and check.
8. You can arrange to get a right facing or left facing pinwheel as per requirement(yellow is facing left in the snap below)
9. Join the squares.I typically align the seams in opposite direction to ensure the points align well and there is no bulk at the joints.

Pinwheel 2

10. Prepare the mug rug will lining the top, batting and lower fabric.I lined the pinwheels with a little running stitch in Perle 8 (red) so its contrasting for some and matching with the solid fabric in others. So I get variety and see how each one looks.
11. While pinning, ensure your pins are away from the Pinwheel as they help hold the batting and rear fabric. Also, it doesn’t interfere with your embroidery. Take the border of the Pinwheel as a guide and complete the embroidery ensuring its through all the 3 layers as its the only quilting that the mug rug will have.

Pinwheel 3

Pinwheel 4

Bind and complete the mug rug!!
I tried double binding with 1.5″ straight bias, wanted it to be narrow and tight when folded.

Hope you like the tutorial. Please drop me a line so I can hop over and see if you make a few of them.The idea is to document for self, as I tend to forget the process and not to reinvent the wheel 🙂

What the kid learns!!
My little one learnt about pinwheels, made some origami paper pinwheels while I sewed my mug rugs and we a read a bit about windmills in general.We went through some holiday snaps when we had spotted windmills during our journey.
With each project I try to ensure that he learns something as well 🙂


A scarp quilt has been on my To-do list for long so when I received this book, Scrap Quilts-Fast and fun as a gift and turned to page 109, I was convinced on giving the ‘String Squares’ a go. As usual though, am not following the pattern in the book.

string squares

Let me write my own tutorial and add modifications to the design !!

Having recently returned from a paper piecing workshop, paper piecing seems the obvious choice 🙂

Quick Strip Quilt: Basic Block Template
All you need:

-A4 sheets
-School rulers(1″ and 1.5″)
-Pencil and eraser
-Fabric scraps and leftovers
-Cutting mat and rotary cutter

Do note that the paper template and hence the block is 8″ when raw and 7.5″ when complete and sewed into a project. You can alter the size of the square and the width of the bands as per your need.

Preparing the paper templates

1. Take an A4 sheet and mark a square 8″ X8″ in size. I used a pencil so the marking is light.

Paper template 1

2. Fold the square to mark the diagonal. Open and draw a line across the diagonal. this will be our guiding line. Place your 1.5″ width scale and align the center of the scale with the diagonal line as seen in the picture below, such that the center of the page has a 1″ width set of parallel line across the diagonal.

Paper template 2

3.Continue to draw parallel lines such that:
The center pair is 1″ apart
then .5″ apart
then 1″ apart and so on until you reach either end of the paper (moving outwards from the diagonal). Please refer to image below for better clarity.

Paper template 3

4. The center 1″ strip would be coloured and so will be each of the alternate strips(.5″). All white strips would be 1″ wide.

Paper template 4

Trim the square and remove extra paper from all sides. Here I have coloured them for easy reference. Also, when you photocopy the coloured areas would look darker and hence easy for guidance and you wouldn’t confuse between white and coloured strips.
Once you are sure that the template is ready, make as many photocopies of it as required. You will sew on these paper templates and tear off the paper at the end .

Cutting fabric and sewing the Block

1.Take all your long scraps. I didn’t have much so I cut strips from my yardage.

Fabric scraps

2. Please note that when you cut your fabric, all white strips are to be cut 1.5″ in width. This is where your 1.5″ width student scale comes to use. It is not used during paper template process.
The center fabric is 1″ when completed , hence has to be cut at 1.5″ width. I chose a maroon tone for this.

All the other coloured fabric would be 1″ when cut(and hence 0.5 inch when completed).

Cut strips

3. Now take a paper template and place the printed side facing down. You basically just see a plain white sheet. Place the maroon along the diagonal and white on top, with right sides of both facing each other.
So, paper template facing down, maroon strip along the diagonal facing up and white strip facing down aligned on the maroon. Hold it against the light to ensure your fabric covers the center band.
Refer image below.

Ensuring correct alignment

4.Pin the strips in place. Always pin on the seam away from you, not like seen below. Turn the paper and sew on one guided line.


5. Turn to the non printed side of the paper, remove the pins and nail press the seams open.You will have one printed and one white band side by side.This is the only strip you have to be really careful about.

Join the third strip

6. Next, place a coloured fabric over the white fabric so that the other seam is aligned for both fabrics. Pin towards the inner seam. Turn and sew on the next guided line. You need not check it against the light but you can never be more careful, just do it as convenient.Turn to teh fabric side, remove pins and needle process. Continue like this until you reach the end of the paper with alternating coloured and white strips.

And the next

7. Iron the untrimmed square inside out. If your coloured strips are not all cotton, then ensure you set your iron to the setting for the fabric that has the lowest tolerance, else you might have some fabric crinkle up and burn.

Uncut square

8. Trim the square to size using your cutting mat and rotary cutter using the paper template as guide.

Trimmed square

Prepare as many blocks you require and use them in various colourful projects ! I have a couple in mind…will soon post on them as well.